← Back to list

P0349 Code in 2011 Ford F150 5.0L: Diagnosis, Symptoms, and VVT Solenoid Repair Insights

Model: 2011 Ford F150 5.0 Fault Code: P0349 Posted: 2021-10-04 14:35

I own a 2011 Ford F150 with a 5.0L engine that has been consistently throwing P0349 diagnostic trouble codes. The vehicle exhibits noticeable performance issues when climbing hills—specifically, it feels like the engine is struggling to maintain power and experiences severe vibration, making gear shifts feel abrupt or unresponsive. The issue first appeared on November 5, 2020, after several days of rough running. At that time, the check engine light (CEL) activated with P0349 code. I took it to my regular mechanic who replaced both intake and exhaust camshaft position sensors as recommended by the OBD-II code. The truck ran smoothly for approximately five months. On April 22, 2021, the symptoms returned—rough idle and vibration—and the CEL came back on with P0349. Each time, the light would turn off before I could observe it during diagnosis, making it difficult to replicate in real-time. The shop consulted a local Ford technician who suggested that the issue might be related to the VVT (Variable Valve Timing) solenoid on the left bank. They replaced the intake VVT solenoid for Bank 2, and the truck ran fine again. However, by September 20, 2021—just five months after the last repair—the symptoms returned. The vibration intensified during uphill driving, and the CEL reappeared about a week later. I was unable to get it into the shop due to scheduling conflicts. A scan at O'Reilly Auto Parts confirmed P0349 again. Over the past week, the light has come on and off intermittently. Currently, the truck runs well under normal conditions but becomes rough and sluggish when climbing hills or accelerating under load. The symptoms appear randomly—sometimes right after starting, other times after 10–20 miles of driving. I’ve been advised that P0349 may indicate a failing VVT solenoid due to intermittent camshaft position signal issues, especially since the code has transitioned from active to 'history' status. I’m concerned about whether this is a recurring issue with 2011 F150s and whether replacing both left bank VVT solenoids (as suggested) will resolve it. I’ve seen similar cases online but would appreciate any real-world experiences or technical insights on diagnosing P0349 in this model. Thanks for your help!

Related fault codes
P0349
Comments (7)
Anonymous 2021-10-05 09:51

Intermittent engine issues are particularly challenging. To properly diagnose, the problem must be duplicated during testing—ideally while symptoms are active. First, which two sensors did the shop replace? Were they only replacing parts without conducting diagnostic tests on the camshaft position circuit? Did they perform scan data analysis or lab scope monitoring? Was the issue a persistent hard fault or intermittent when you first brought it in? Could they observe your driving conditions and replicate the problem during inspection? What exactly did the repair notes say about the intake cam sensor history code? Were both VVT solenoids on the left bank replaced as recommended? The symptoms returned after five months—was that consistent with previous repairs? Is the issue intermittent or constant now, and does it worsen under load? Can you confirm if the problem occurs specifically when climbing hills?

Anonymous 2021-10-05 12:38

Thanks for the detailed response. I’ve taken the truck to the same shop twice—both times the check engine light was off when I dropped it off. I personally tested it at O'Reilly Auto Parts, and they confirmed P0349. The first visit: they replaced both the left intake and exhaust camshaft position sensors. After that, the truck ran smoothly for five months. On the second visit, the symptoms returned—running rough until the CEL came on, then went off. I couldn’t reproduce it during the test. In their repair notes, they noted a history code for P0349 Bank 2 intake cam sensor and stated: 'A stretched timing chain or faulty sensor is unlikely to cause intermittent failures over long periods. A failing VVT solenoid adjuster may intermittently misalign the camshaft position, leading to this code. While we cannot confirm current failure, past experience with this model suggests VVT solenoids are a common issue. Recommend removing the left valve cover and replacing both VVT solenoids on the left bank.' This repair was completed in April 2021. The symptoms returned on September 20, 2021—about five months later—and the CEL didn’t come on until about a week later. I couldn’t get it into the shop due to scheduling conflicts. A scan at O'Reilly confirmed P0349 again. Over the past week, the light has flickered on and off. It’s currently off when I scheduled my appointment—so I canceled. The truck runs fine under normal conditions but becomes rough and bogs down during uphill climbs or acceleration. This behavior appears random: sometimes right after starting, other times after 10–20 miles of driving. For example, Monday it didn’t start until about 20 miles into the drive. I hope this clarifies everything. Thanks for your input.

Anonymous 2021-10-05 17:31

So you're saying the issue can be reliably reproduced when driving uphill? I thought intermittent problems were hard to duplicate. The PCM monitors camshaft position after commanding VVT solenoids—any mismatch will trigger a P0349 code. Have you seen cases where faulty crankshaft sensors cause false cam sensor codes? Could you confirm whether the problem occurs specifically during hill climbing or under load, and if there’s any pattern in when it starts?

Anonymous 2021-10-06 07:18

The issue is intermittent but becomes significantly worse under load—especially when climbing hills. There's no consistent trigger; sometimes it appears immediately after starting, other times it develops after a few miles of driving. For instance, on Monday, the problem only started about 20 miles into my drive.

Anonymous 2021-10-06 07:27

You’ll need to visit an ASE-certified technician or dealership with proper diagnostic tools and experience in engine electronics. A lab scope should be connected to monitor signal integrity on the camshaft sensor wiring, while scan tool data (PIDs) must be observed during symptom reproduction. Check fuel trims and O2 sensor readings as well—these can indicate underlying misfires or sensor drift. Most local shops lack understanding of PCM circuit design or advanced diagnostics. The key challenge is duplicating the issue in real time with test equipment connected. I’ve seen this happen many times over 30 years—without proper testing, diagnoses are often inaccurate.

Anonymous 2021-10-06 07:31

Thanks for your advice—I’ll schedule an appointment with the dealership soon. Will update everyone once it’s fixed. Thanks again!

Anonymous 2021-10-06 07:44

You're welcome! I hope you get a solid diagnosis and resolution. Please keep us updated on the outcome—this would be helpful for others experiencing similar issues with their 2011 Ford F150.