← Back to list

1996 Nissan Sentra OBD P0500 and P0400 Codes: Causes, Fixes, and Smog Test Solutions

Model: 1996 nissan sentra Fault Code: P0400 Posted: 2006-10-30 18:53

I'm facing two OBD-II diagnostic codes—P0500 and P0400—on my 1996 Nissan Sentra while preparing for an annual smog test. My mechanic claims only the dealership can fix these issues, but they refuse to provide a cost estimate or confirm whether repairs will pass the emissions test. The car runs smoothly, and I've noticed that the speedometer works normally. However, the check engine light remains on. The P0500 code is suspected to be related to the vehicle speed sensor. While the speedometer appears functional, some reports indicate that even when the speedometer reads correctly, the signal sent from the speedometer head to the Engine Control Module (ECM) may be faulty or absent—this can trigger the P0500 code. For the P0400 code, which relates to the EGR (Exhaust Gas Recirculation) system, possible causes include a malfunctioning EGR solenoid valve. Other potential issues in the EGR system could also contribute. Since multiple components are involved, a full EGR system inspection is typically required to identify the root cause. I’ve found that replacing the speedometer head (especially if it's integrated with the odometer) can resolve P0500. However, if the odometer is part of the unit, the mileage must match the current reading—dealerships often charge a fee for adjusting this. For vehicles like my 1996 Sentra, I recommend providing the VIN and current odometer reading to ensure compatibility. I’m seeking reliable, cost-effective solutions that don’t require dealership-only repairs. Any insights or experiences with these codes on older Nissan models would be greatly appreciated.

Related fault codes
P0400P0500
Comments (2)
Anonymous 2006-10-31 08:06

A mechanic who believes only dealerships can fix P0500 and P0400 codes is not providing practical advice. The P0500 code on a 1996 Nissan Sentra may stem from a faulty speedometer head, even if the speedometer display appears normal. In several cases I've seen, the issue lies in the signal transmission from the speedometer head to the ECM—there's no output at all. Replacing the speedometer head has resolved this problem on multiple models. For P0400, it’s typically linked to EGR system faults, with a defective EGR solenoid being one of the most common culprits. Since the EGR system involves several components, a full diagnostic is needed to pinpoint the exact failure. A simple replacement may not suffice—system-level testing is essential. If your Sentra has an integrated odometer in the speedometer head, ensure you provide your VIN and current mileage when ordering a replacement part. Dealerships will charge for mileage adjustment, and they may not sell the unit without it. I recommend sourcing a new part directly from a Nissan dealer with correct mileage settings to avoid future issues. Good luck—this is a common issue on older Nissans, and solutions exist outside of dealership-only services.

Anonymous 2007-02-20 11:37

As with many Nissans that I have worked on the PO500 code could be caused by a problem with the speedometer head itself. You mentioned that the speedometer works fine but I have seen this problem in the past and on the cars that I fixed the speed sensor code was present and the speedo also worked normal. What I have found was that the signal from the speedometer head to the ECM/computer was bad. There was no output signal from the speedo head itself. I have replaced the speedometer head on several Nissan models to fix the problem. Discover more Internet forum OBD Car dealership You could try a used part but if the odometer is part of the speedo head the mileage may not match what you need. I prefer to order a new part from a Nissan dealer. If your sentra has the odometer built in you will need to provide the dealer with your VIN#/ vehicle ID number and the current reading on your odometer so they can order the part with the correct mileage on the new odometer. The dealer charges a fee to adjust the mileage on the new part and I'm not sure if they will sell it without the mileage adjustment. The PO400 code could be any one or more possible things which are related to the ERG system. One of the problems I see on many of the Nissans I've serviced is a faulty EGR solenoid valve. You will need to have the EGR system serviced to find the exact problem since there are many other possibilities. Good Luck!!!